|
|
BOREHOLES
¨ Ground Bearing Determinations.
¨ SPT’S and Vanes in-situ.
¨ Subsidence Investigations.
¨ Water Table Monitoring.
¨ Methane Monitoring.
¨ Deep Level Datums.
¨ Contamination Investigations.
¨ Undisturbed Samples for Triaxials.
¨ Sample Recovery for Laboratory
Testing.
|
OTHER SERVICES
¨ Dynamic Probe testing.
¨ Soakage Tests (to NHBC Spec
or BRE 365).
¨ Trial Pit Excavation.
¨ All laboratory testing done
by UKAS approved labs.
¨ CBR and CLEA - Defra Sampling
Testing (with MCert accredited lab) and reporting.
¨ Walk Over Surveys to NHBC
CH4.1 - D2.
¨ Brownfield and Derelict Site
Investigations.
¨ PTS trained technicians and
Link-Up Network Rail Approval.
|
Main Chassis
Fabricated from box section incorporating drop weight, supports, engine mounting and controls.
Drop Hammer
Two piece weight 50kg and 13.5kg for dcp or spt testing.
This runs on two rails and is full guarded with mesh.
Trip Hammer speed: 0 – 50 blows
per minute
Trip Hammer drop: 500
– 750mm
Trip Hammer weight: 50 or 63.5kg
Mast Assembly& Dimensions
Fabricated with box section, mast connected by hinge pin to main chassis, hydraulically raised
and lowered.
Overall height: 2.4 – 2.85m
Width:
0.6 - 0.8m
Hydraulic Power Pack
This is powered by a 16HP water-cooled diesel engine and provides power for drilling, rigging and
tracking.
Flow for PTO:
30 l/min
Working pressure: 175
bar
Tracks
Purpose built crawler with rubber tracks, fitted with a tilt mechanism to allow working on slopes.
Crawler width: 0.8m
Overall length: 1.5 - 2.7m
Total weight:
1300kgs
light (DP-L), medium (DP-M)
and heavy (DP-H) dynamic sounding with Honda engine.
This
unit is powered by a reliable 4-stroke petrol engine which transmits ist revolutions through a centrifugal clutch and a robust
gearbox to the rotating chain integrated in the mast body. Thus the unit is independent from other energy sources and can
be operated everywhere. The number of blows per minute (between 15 and 30) is controlled by adjusting the engine speed at
the throttle lever.
TECHNICAL DATA:
basic weight: ca. 125 kg
total height: 2.340 mm
width:
780 mm
length: 785 mm
rod/tool length: 1.200 mm max.
to set up the mast vertically:
lateral inclination 10
degrees
frontal inclination 10 degrees
blows per minute: 15 - 30, adjustable
drop weight mass:
basic weight 10 kg
plus 20 kg 30 kg
plus 20 kg 50 kg
drop height: 500 mm
Honda engine
type GX100
aircooled 1-cylinder 4-stroke
97 cm³ , 1,9 kW, leadfree fuel,
1,4
l fuel reservoir capacity,
noise level 75 dB(A) at 3600 RPM
An extremely versatile dcp which can be used
anywhere.
Specification:
Height: max 1.8m
Width: 0.4m
Weight: 10kg
Drop: 0.5m
Manufactured in hardened steel, this light
versatile rig packs into 2 rucksacks (or
a
wheelbarrow) to allow dcp testing in the
most
inaccessible locations.
This rig pushes a sacrificial nose-cone into
the
ground to measure the resistance/strength. These
measurements can then be interpreted to SPT’s.
The T13 provides a quick reliable solution
for the
limited access, high volume projects where
sampling is not required.
Download a copy of our Digital Brochure |
click here to download file
Downlod a copy of our Rental Brochure |
click here to download file
|
